EstimationPro AI EstimationPro AI

HVAC Proposal Template (Free, Printable)

Free HVAC proposal template. Put Good, Better and Best system options side by side, price each from your cost and margin, then print it or save it as a PDF.

Built by a 20-year contractor By Brad

Last updated: 2026-11-06

This HVAC proposal template is built for system replacements, where the homeowner is choosing between options. Fill in what you found and the design load, then build up to three systems (Good, Better, Best) side by side with efficiency, refrigerant, warranties and one installed price each. Each price is worked out from your equipment, materials, labor hours and permit at the margin you set, and the template shows what you keep. Add-ons sit below for the client to initial, and the proposal ends with a check-one box and signature lines. Print it or save it as a PDF. Doing the in-home visit first? Print the blank form. A worked 3-ton replacement proposal is below.

Doing the in-home visit first?
Your Company
Client, Home and What You Found
Your Costs (the client never sees these)

Every option price below is built from these: (equipment + materials + labor hours × labor cost + permit) ÷ (1 − margin), rounded up to the dollar.

Share of the price you keep for overhead and profit

System Options

Fill in one, two or three options. Enter equipment and materials at what you pay, including any sales tax you pay on them. Leave the price blank to use the suggested price, or type your own. An option with no price is left off the proposal.

Optional Add-Ons

Priced on the proposal for the client to initial. Not in any option price.

Scope, Schedule and Payment

Enter equipment cost and a margin (or a price) for at least one option.

Free to use. No signup needed.

How to Write an HVAC Proposal

What goes in it, pricing Good-Better-Best options from cost and margin, a worked 3-ton proposal, and the 2026 efficiency, refrigerant and tax credit lines.

HVAC Proposal vs HVAC Estimate: What Changes

An HVAC estimate prices one job. An HVAC proposal sells a decision. On a system replacement the homeowner is usually choosing between two or three systems at different prices, so the proposal puts what you found, the options side by side, what every option includes, and one signature that picks an option on the same few pages. If you only need to price a repair or a single system, the HVAC estimate template is the shorter tool.

  • Header: company, license numbers, client, job address, date, and how long the prices are good for
  • What you found: the existing system and its age, the comfort complaints, the design load from your load calc, and your recommendation in plain words
  • Options: for each one, the outdoor and indoor equipment, efficiency (SEER2, HSPF2 or AFUE), refrigerant, equipment and labor warranty, and one installed price
  • Included in every option: removal and disposal, refrigerant recovery, pad, disconnect, line set, condensate, thermostat, permit, start-up and commissioning
  • Optional add-ons: priced separately for the client to initial, so the base price stays clean
  • Not included: duct replacement, panel upgrades, drywall and concealed conditions, unless listed
  • Schedule, payment and acceptance: install timing, deposit and balance, and a signature block where the client checks one option

Jobber's HVAC proposal template uses close to the same skeleton (inspection findings, project summary, services and costs, terms, signature page). AroFlo's guide gives a good test for the scope: write it so a technician who was not on the survey could price the job from the page alone.

Key Takeaways

  • A proposal compares options; an estimate prices one job
  • Put the design load and what you found before the prices
  • One signature block where the client checks one option

How to Price Good, Better and Best Options

Price every option from your cost, then divide by (1 − your target margin). Cost is the equipment and materials at what you pay, the labor hours times your burdened labor cost per hour, and the permit. ServiceTitan's HVAC proposal guide calls offering options in a Good Better Best format industry best practice, and says to let the customer choose rather than assuming they want the most expensive one.

  • Change one or two things per step, not everything. A common ladder is single-stage to two-stage to variable-speed equipment, or a straight AC and furnace to a heat pump with the furnace as backup (dual fuel)
  • Labor hours change too. If a higher option takes longer to set up, wire and commission, give it more hours instead of copying the Good option's labor line
  • Margin is not markup. A 30% margin means you keep 30 cents of every dollar of price, which takes a 42.9% markup on cost (0.30 ÷ 0.70). Adding 30% to cost only gets you a 23.1% margin. The builder above shows the markup that matches your margin
  • Use your own labor cost, wage plus payroll taxes, comp and benefits, not the wage alone. The burdened labor rate calculator works it out, and the overhead rate calculator helps you set a margin that covers the shop, trucks and office

ServiceTitan describes two ways to build the tiers: progressive, where each tier adds equipment or services to the one below, and additive, where the client adds or removes items. The template above is progressive for the systems and additive for the add-ons.

Key Takeaways

  • Price = cost ÷ (1 − margin), rounded up
  • A 30% margin needs a 42.9% markup, not 30%
  • Each option gets its own equipment, materials and labor hours

Worked Example: 3-Ton Furnace and AC Replacement Proposal

Here is a full three-option proposal for a 1,800 sq ft two-story house with a 19-year-old 3-ton AC and 80% gas furnace. The load calc came in at 33,500 Btu/h cooling, so every option is 3 tons (36,000 Btu/h). The $60 an hour burdened labor cost, the 16, 18 and 20 labor hours, the 30% target margin and the $250 permit are example inputs, and the equipment and materials figures are placeholders for the math. Use your own labor cost, your crew's hours and your distributor's quote.

Line Good Better Best
System14.3 SEER2 single-stage AC, 80% AFUE furnace16 SEER2 two-stage AC, 96% AFUE two-stage furnace17 SEER2 / 8.5 HSPF2 variable-speed heat pump, 96% AFUE furnace (dual fuel)
Equipment$3,400$4,600$5,600
Materials (line set, pad, disconnect, whip, condensate, thermostat)$650$900$1,000
Labor at $60/hr16 hrs = $96018 hrs = $1,08020 hrs = $1,200
Permit$250$250$250
Your cost$5,260$6,830$8,050
Cost ÷ 0.70$7,514.29$9,757.14$11,500.00
Installed price (rounded up)$7,515$9,758$11,500
You keep$2,255$2,928$3,450

Each "you keep" figure is 30% of its price ($2,255 ÷ $7,515, $2,928 ÷ $9,758 and $3,450 ÷ $11,500). Two add-ons go below the options for the client to initial: duct sealing for minor leaks at $450, and a smart thermostat upgrade on the Good option at $300. Neither is in an option price.

The labor warranty is a lever you control: this example offers 1 year on Good, 2 on Better and 5 on Best, with the manufacturer's parts warranty listed as it reads on the spec sheet for each system.

Sanity check: national installed ranges for a full furnace-and-AC replacement run roughly $5,500 to $12,000, so all three options land inside it. The Best option sits near the top because it adds a heat pump to the furnace. Prices vary by region, so check your own market and get your distributor's current equipment pricing before you send it. The HVAC installation cost calculator gives a quick range by system type.

Key Takeaways

  • Good $7,515, Better $9,758, Best $11,500 at a 30% margin
  • Add-ons sit below the options and are initialed separately
  • Labor warranty length is a tier lever you control

Efficiency, Refrigerant and Tax Credit Lines in 2026

Three lines on a 2026 HVAC proposal need checking before you send it: the efficiency rating, the refrigerant, and anything you say about tax credits.

  • Efficiency minimums depend on region. DOE's 2023 standards set split-system heat pumps at 14.3 SEER2 and 7.5 HSPF2 nationwide. Split-system air conditioners need 13.4 SEER2 in the North, but 14.3 SEER2 in the Southeast and Southwest for units under 45,000 Btu/h (13.8 at 45,000 and up), and the Southwest adds an EER2 minimum (11.7, or 9.8 for units rated 15.2 SEER2 or higher, under 45,000 Btu/h). In those two southern regions the rule goes by installation date, and DOE says it is illegal for a contractor to install a unit that does not meet it. So a 13.4 SEER2 "Good" option only works up north
  • Name the refrigerant on every option. NAHB reports the industry is moving to lower-GWP refrigerants known as A2Ls. EPA's final rule, reported by NAHB on May 26, 2026 and effective July 27, 2026, lets contractors keep installing R-410A units made or imported before January 1, 2025 until that stock runs out. New York's state law still holds the original January 1, 2026 deadline. If an option is leftover R-410A stock, say so on the proposal
  • Do not promise the federal tax credit. The IRS says the Energy Efficient Home Improvement Credit is allowed for qualifying property placed in service before December 31, 2025. A system installed in 2026 does not qualify, so take any "up to $2,000 tax credit" line out of old proposal templates. Utility or state rebates may still apply; name the program only after you check it
  • Size it and show it. Put the design load from your load calculation on the proposal. Check your local code for what the permit office wants. The HVAC load calculator gives a starting point
  • Refrigerant work needs certification. EPA's Section 608 rules require technicians who maintain, service, repair or dispose of equipment that could release ozone-depleting refrigerants to be certified. You can put your certification number in the proposal header next to your state license

Key Takeaways

  • Southeast and Southwest AC under 45,000 Btu/h: 14.3 SEER2 minimum
  • R-410A units made before 2025 can still be installed (not in New York)
  • The federal 25C credit ended with 2025 installs

Scope, Exclusions and Payment Terms That Prevent Fights

Most proposal fights start with something that was never written down. I tell homeowners to compare bids apples to apples, because the cheapest bid usually leaves things out. An HVAC proposal that spells out what every option includes is the one that holds up when a homeowner lays three bids on the kitchen table.

  • Line set: say whether you are replacing it or flushing and reusing it. Two bidders can price it very differently, and the homeowner should be able to see which you did
  • Electrical: a new disconnect and whip are usually in scope; a new circuit, a bigger breaker or a panel upgrade usually is not. Say which
  • Ducts: if you did not price duct work, write "existing ductwork reused as is" and offer sealing as an add-on
  • Concealed conditions: state that anything found after work starts is priced as a change order before that work is done
  • Deposit: check your state's rules. California's contractor board says a home improvement down payment cannot be more than $1,000 or 10% of the contract price, whichever is less, and later payments cannot run ahead of the work done or materials delivered. On the Best option above, 10% would be $1,150, so the California cap is $1,000
  • Expiry: equipment prices move, so give the prices a clear "good for" date

ServiceTitan's guide also suggests offering financing on bigger jobs. If you do, name the lender and terms only as the lender publishes them.

Key Takeaways

  • Spell out line set, electrical and duct scope on every proposal
  • Concealed conditions become a change order before the work
  • California caps deposits at $1,000 or 10%, whichever is less

Send It, Then Follow Up

A proposal that is sent and never chased is a coin flip. Jobber's guide says to follow up within 48 to 72 hours, and to try again if there is no reply after a week or two. I'm a remodeler, not an HVAC contractor, but the lesson is the same in every trade: a lot of jobs are won on the second or third follow-up, not the first send. Most contractors never chase the bid, so the one who does stands out.

On the follow-up call or text, ask which option they are leaning toward. A homeowner stuck between Better and Best is a different conversation from one who has not opened the proposal yet.

If you would rather not build proposals by hand, EstimationPro builds Good-Better-Best estimates from photos, a voice walkthrough or typed notes, with labor and material rates adjusted for your region, and you review every line before it goes out. Send it from EstimationPro and the client gets an automatic reminder at 24 hours if they have not opened it, another 48 hours after they open it with no response, and a final one at 7 days. I use that follow-up on my own jobs. One estimate is $9, or plans run $79 or $149 a month. It is not a dispatch or crew-routing platform.

Key Takeaways

  • First follow-up within 48 to 72 hours
  • Ask which option they are leaning toward
  • Jobs are often won on the second or third follow-up

How to Use This Calculator

Fill In the Home and What You Found

Enter your company and license numbers, the client and job address, the home, the existing system, the design load from your load calculation, and what you found and recommend in plain words.

Enter Your Costs

Type your burdened labor cost per hour, the margin you want to keep and the permit fee. The template shows the markup that matches your margin. The client never sees these numbers.

Build Up to Three System Options

For Good, Better and Best, describe the equipment, efficiency, refrigerant and warranties, then enter equipment and materials at your cost and the labor hours. The template suggests each installed price from (cost ÷ (1 − margin)), rounded up, and shows what you keep. Type your own price to override it.

Add Scope, Terms, Preview and Print

Edit what every option includes and what is not included, add optional add-ons for the client to initial, set the schedule, deposit and how long prices are good for. Preview shows the options side by side with a check-one box and signature lines. Print it or save it as a PDF, or print the blank version for the in-home visit.

Free to Embed on Your Website

Add this calculator to your blog, resource page, or client portal — just copy one line of code. Your visitors get a useful tool, you get more engagement.

100% freeAuto-resizesMobile responsiveNo sign-up required
EstimationPro AI For Contractors, By Contractors

Go Beyond Templates With AI-Powered Estimates

Templates are a start. EstimationPro generates complete, customized estimates from your project details.

Photos & voice to estimate PDF proposals & schedules Regional pricing data
Price one real job for $9. 30-day money-back guarantee. Automatic client follow-up Built by a contractor who uses it on his own remodeling jobs

Frequently Asked Questions

What should an HVAC proposal include?

Your company and license numbers, the client and job address, what you found (existing system, age, comfort complaints, design load), one to three system options with equipment, efficiency, refrigerant, warranties and one installed price each, what every option includes, optional add-ons priced separately, what is not included, the schedule, deposit and payment terms, how long the prices are good for, and a signature block where the client checks one option.

How do I price Good, Better and Best HVAC options?

Price each option from its own cost: equipment and materials at what you pay, labor hours times your burdened labor cost, and the permit. Then divide by (1 minus your target margin). In the worked example above, a $5,260 cost at a 30% margin is $5,260 ÷ 0.70 = $7,514.29, rounded up to $7,515. A 30% margin takes a 42.9% markup; adding 30% to cost only gets you a 23.1% margin. The profit margin calculator checks the math.

Can I still put the federal tax credit on an HVAC proposal?

Not for a system installed in 2026. The IRS says the Energy Efficient Home Improvement Credit is allowed for qualifying property placed in service before December 31, 2025. Remove any federal tax credit line from older proposal templates. Utility and state rebates are separate; name a program only after you confirm it covers the equipment you are proposing.

Can I still install R-410A equipment?

As reported by NAHB on May 26, 2026, EPA's final rule (effective July 27, 2026) allows installing R-410A units manufactured or imported before January 1, 2025 until that stock runs out. New York's state law keeps the January 1, 2026 deadline. Whatever you propose, put the refrigerant on each option so the homeowner can compare bids.

How big a deposit can I ask for on an HVAC replacement?

It depends on your state. In California, the Contractors State License Board says a home improvement down payment cannot be more than $1,000 or 10% of the contract price, whichever is less. On an $11,500 system that is $1,000, not $1,150. Check your own state's contractor rules before you set the deposit in the template.

Related Tools and Articles

Sources

What EstimationPro Does for Contractors

Photos, Voice or Notes In

Describe the job with photos, a voice walkthrough or typed notes and get priced line items for labor and materials. Contractors save 2+ hours per estimate.

Priced for Your Area

Labor and material rates are adjusted for the job's location. You review and edit every line before it goes out.

Automatic Follow-Up

Send the estimate from EstimationPro and your client gets a reminder at 24 hours, 48 hours and 7 days. Many jobs are won on the second or third follow-up.

PDF, Link and Payments

Export a PDF or share a link your client can approve. Collect payments online with Stripe; deposits, milestone schedules and invoices are on Pro.

Related Free Tools

Estimating software for HVAC contractors

Photos, voice or notes in, a priced estimate out.

Try EstimationPro AI

Turn this job into a full, priced estimate for your client.

Snap photos, talk through the scope, drop in your notes. The AI prices every line item with labor and material rates adjusted for your region, and checks the math.

30-day money-back guarantee Automatic client follow-up Built by a 20-year contractor
Get started Price one real job for $9. 30-day money-back guarantee.
Go beyond templates with AI estimates